![Setup Is Inspecting Your Hardware Blank Screen Setup Is Inspecting Your Hardware Blank Screen](http://www.windowsreinstall.com/winxppro/images/Image2.gif)
. just a blank screen. Immediately following the 'Setup is inspecting your hardware. Setup will start inspecting your computer hardware and.
Matthew S. Dippel - The Official Blog: Blank Screen after Setup is Inspecting your computer's hardware configuration in Windows XP. It's been a little while since I've been able to write, but this one hit me again this weekend, and again I spent hours trying to figure out what was going on. The symptom is this: Blank Screen occurs when "Setup is Inspecting your Computer's Hardware Configuration"or. Blank Screen before Setup even starts. Further, waiting it out does nothing. The drive eventually spins down and the PC is unresponsive.
![Setup Is Inspecting Your Hardware Blank Screen Setup Is Inspecting Your Hardware Blank Screen](http://us.informatiweb.net/images/tutoriels/R%C3%A9paration/Windows%20XP/Windows%20XP%20Pro%20-%20tuto%20drivers-2012-11-18-13-13-55.jpg)
Of course, the monitor never goes to DPMS mode, so it looks like the video card is still receiving a signal. This saga was part of my other adventure. The cause of the black screen is simple: Windows XPs setup utility cannot properly read the hard disk partition tables. I'm not sure if it chokes on every linux installation, or the specific LVM setup I had done with Fedora 7, but the hang immediately after setup starts is usually always unreadable partition tables. A couple of fixes to try: Unplug every hard drive and USB, Compact Flash, SD, or other "hard drive like" device, except for the one you intend to boot from and install the operating system to. Try to rerun setup.
If successful, plug in a drive at a time after Windows is installed and updated. If that doesn't work, you still have options, but the only ones I can present to you will cause your data to be destroyed, so here's hoping you have a backup.
- Experts Exchange > Questions > Blank screen after 'Setup is inspecting your computer's hardware. just a blank screen. if you unplug your IDE harddrive, setup.
- . blank screen after 'Setup is inspecting your hardware's configuration'. get the 'Setup is inspecting your hardware's current configuration' message.
- Windows setup hangs at 'Setup is inspecting your computer's hardware. past the 'Setup is Inspecting.' screen and you can. a disk blank slate and that.
- 'Setup is inspecting your hardware. setup inspecting hardware. as some may assume looking at the screen. Thus don't waste your time investigating.
- Blank Screen after Setup is Inspecting your computer's hardware configuration in Windows XP.
Download Knoppix (or a Linux based live CD that comes .. Burn the CD/DVD on another computer. Boot Knoppix .. wait. When the GUI comes up (or perhaps "if" the GUI comes up), hit CTRL+ALT+F2, this will get you to a "root shell" in text mode. The reason I prefer this route is that it doesn't require a working mouse, which I didn't have since Knoppix couldn't initialize it)type "fdisk /dev/sda", if the hard disk you're dealing with is SCSI or SATA, otherwise type "fdisk /dev/hda" if the hard disk you're dealing with is IDE/EIDE/PATA.
Windows XP Setup Blank Screen > Windows XP Setup Blank Screen. Tags: Gateway. the next screen That say's ' Setup is inspecting your Hardware configuration'. Blank screen - cannot reach setup screen. 'Setup is inspecting your computer's hardware. So far have not gotten first drive to be seen but my blank screen.
If you have one partition, type "w" (writes out the partition table), and shut down. If you have more than one, type a partition number and repeat until all partitions are gone. You can verify that all partitions are deleted by hitting "p", and seeing if any show up. Note that after you hit "w", you're going to lose all of the data on the partitions that you have deleted. Rerun Setup. If you're comfortable with partitioning, skip step 6 and start by hitting "p". This will list out all partitions on that drive. You may find a particular partition that looks suspect.
Try deleting the suspect partition and leaving the ones that look good, then rerun setup. Of course, you've booted to a Knoppix CD, so you might try using some of the tools that are included with Knoppix to diagnose your problems, recover some of your data and copy it to another computer or drive, or do any other number of recovery/hardware tests. In my case, the data was already gone, so wiping out the partitions was an easy choice.
Windows setup hangs at "Setup is inspecting your computer's hardware configuration". THE SOLUTION: I spent hours online looking for a fix and so many sites suggested this was a hardware problem. I was very skeptical of those suggestions. I still don't know exactly WHAT causes the problem, but it's not hardware.
It's something with Windows XP. Here's how I got around it: Get a copy of Linspire (Linux based operating system) off the net. Burn the ISO to CD. Boot from CD but BE SURE TO SELECT "RUN LINSPIRE FROM CD" or LINSPIRE LIVE. Go to the Linux disk formatting utility - - I forget the name. It is listed under "Run Programs" then "Utilities". Delete the active partition on the hard drive.
You may also have to create a NTFS partition that is smaller than the hard drive using this utility. Save the changes. Close out of Linspire.
Reboot with Win XP CD and you will get past the "Setup is Inspecting . Windows. Because of the prior problem I had with installation, I chose a NTFS partition that was considerably smaller than the total size of the hard drive. It works fine now.