Fox Rp23 Service Manual >>>CLICK HERE<<< Fox Racing Shox Tuning Tips. Tracking Hackers Through Cyberspace Pdf · Fox Float Rp23 Service Manual · Cps. After reading up on the Fox RP23 manual I now understand the Pro Pedal. . Rear Shocks > FLOAT > FLOAT RP23. FLOAT RP23. Internal service should be performed by FOX Racing Shox or an Authorized Service Center. Float Rp23 Boost Valve Manual Boost Valve Air Shock FOX SERVICE OWNERS MANUAL 2000 FLOAT VANILLA FORK. Fox Float RP23 Factory series boost valve. Get Instant Access to eBook Fox Float R Manual PDF at Our Huge Library. FOX. Fox Float Rp2 Drcv Manual As with the ProPedal lever, reputation. have with PDF FLOAT RP2, RP3. RP23 DRCV - FOX Redefining Ride Dynamics 2006 REAR SHOCK OWNERS MANUAL 25. MAINTENANCE. Fox Rear Shock Float RP2 2011 Factory. Fox Float Rp23 Manual Pdf fox float rl, instructions for float rl rear shock Pedal Locked Open K2 Download free pdf files,ebooks and documents of fox float rl rear shock manual. Green Fox Shox Float RP23 Fox (96)Alps 4, (07.
FLOAT RP23 REAR SHOCK. Installing Your Shock | General Maintenance | Before You Ride | Measuring Sag | Setting. Internal service should be performed by FOX Racing Shox or an Authorized Service Center. Before You Ride.
FLOAT RP2. 3Installing Your Shock | General Maintenance | Before You Ride | Measuring. Sag | Setting Sag | Adjusting Rebound | Pro.
Pedal | Stuck Down Shock | Air Sleeve Maintenance | Service Intervals | Important Safety Informationfeatures/adjustmentshigh volume standard air sleeve, boost valve, angled air valve, lightweight chassis, DOHC Pro. Pedal lever with 2 positions, Pro. Pedal tuning range adjuster with 3 positions, air spring pressure. Installing Your Shock. If you are installing your shock on a bike for which the shock is not. Install the shock. Remove the main air.
Carefully cycle the. Check that all parts. Pressurize your main. You will. tune to a more specific air pressure in the Setting.
Sag section below. Set. sag. General Maintenance. There may be a small amount of air sleeve lubricant residue on the body. This is normal. If this residual air sleeve lubricant is not present. Some. other things to consider for all shock models: If you ride in extreme. Check. the maintenance schedule for your shock.
Wash your shock with soap. Do not use a high pressure. Internal service should. FOX Racing Shox or an Authorized.
Service Center. Before You Ride. Clean the outside of your shock with only mild soap and water. Note: Do not use any solvents or de- greasers, as these products can damage the shock's exterior finish or its anodized parts. Do not spray water directly on the seal/shock body junction. Do not use a on your shock. Inspect the entire exterior of your shock. The. shock should not be used if any of the exterior parts appear to be damaged.
Contact your local dealer. FOX Racing Shox for further.
Make sure that your quick- release levers (or thru- axle. Check your headset adjustment. If loose, adjust it accordingly.
Check that all brake cables or hoses are properly. Test the proper operation of your front and rear brakes. Setting Sag. To set sag: Measure. Air Spring Setting Guidelines table. Air Spring. Setting Guidelines. Shock Travel(in./mm)2. Sag(in./mm)1. 0. 0/2.
If your measured sag value doesn't match the table value, add or release air pressure in 5 PSI increments. If necessary, measure and set sag again and repeat this adjustment. If necessary, measure and set sag again and repeat this adjustment. Repeat until your target sag is achieved, then replace the air valve cap. Adjusting Rebound. Rebound controls the rate at which your shock returns after it has been. The proper rebound setting is a personal preference, and changes.
A rule of thumb is that. The rebound knob has 8- 1. For slower. rebound, turn the red adjuster knob clockwise. Pro. Pedal. Pro. Pedal Lever. The Pro. Pedal lever allows for on- the- fly.
Pro. Pedal adjustment. Pro. Pedal damping reduces pedal- induced suspension. The two Pro. Pedal lever settings are.
Use each setting to adjust the shock for. For example, use PROPEDAL. OPEN for the descent. To determine which Pro. Pedal position is better. Switch between positions and select the one that reduces suspension.
Because suspension designs and riding skills. For more precise Pro. Pedal tuning and to further eliminate pedal- induced. Pro. Pedal knob. As with. Pro. Pedal lever, switch positions and select a setting that reduces. Pro. Pedal Knob. The 3- position Pro.
Pedal knob allows you to adjust Pro. Pedal firmness when the Pro. Pedal lever is in the. PROPEDAL position.
The Pro. Pedal. knob only changes damping when the Pro. Pedal lever is in the PROPEDAL. The Pro. Pedal knob settings are denoted by.
Pro. Pedal knob. The three Pro. Pedal knob settings. PROPEDAL Light(2) PROPEDAL Medium(3) PROPEDAL Firm.
To adjust the Pro. Pedal knob: Turn the Pro. Pedal lever. to the PROPEDAL position. Lift the Pro. Pedal knob.
Turn the Pro. Pedal knob. Pro. Pedal knob facing the user) until the selection. Pro. Pedal lever (#3). The Pro. Pedal knob clicks twice per setting as it turns. The first click. occurs as you exit the current setting; the second click as you engage. Push the Pro. Pedal knob. CAUTION: For safety reasons, the Pro.
Pedal knob setting should only be changed when you're not riding the bicycle. Bushing. Technology & Inspection | Seals & Foam. Rings | Control. Direction | Oil Volumes | Structural. Inspection | Dropout Thickness Inspection | Torque Values | Unit. Conversion | Suspension Tuning Tips | Using. Pump | Important Safety Information | Service Intervals | Contact FOX Service | Warranty Information | FOXHelp Service Web Site. Copyright © 2. 01.
CDATA[ ]]>FOX Factory Inc.